polystyrene sheet for Construction

Specifications of polystyrene blocks (ceiling foam) manufactured by Haierfam Company:

• Block width from 50 to 70 cm
• Block length from 1 to 2 meters
• Height from 10 to 30 cm
• Density from 1 kg / m3 to 2 kg / m3
• Advantages of using Haierfam polystyrene blocks (ceiling foam):
• Replacement of 5.2kg polystyrene blocks with ten 120kg clay blocks
• 25% savings on foundation and skeleton cost considering low block weight
• Saving on joists due to proper width of blocks
• The use of these blocks is supported by the Fuel Optimization Organization
• Speed and ease of execution of roofs, and the absence of waste in transportation to the floors
• These lightweight blocks minimize the risk of material collapse during an earthquake.
• Due to the type of expanded polystyrene material, these blocks are the best insulation in terms of penetration of moisture, heat, cold and sound and prevent up to 70% of energy loss.
• Roof blocks

Advantages and features of using Plastofoam blocks

• 70% energy saving
• Weight loss of structures
• Reduce concrete volume by 30% and steel by 25%
• Earthquake-safe due to flexibility over other building materials
• Fireproof and burn-resistant
• Reduce project execution time
• Reduce shipping cost
• Sound, heat, cold and humidity insulation
• Save plaster and soil coating
• Optimal management in project control
• Increase the useful life span of the building
• Reduce molding costs
• Insect penetration resistant

Polystyrene foam insulation sheet

Polystyrene insulation is one of the types of cold insulation that can easily be used for insulating walls, ceilings, and floors inside or outside the building.
Thermal insulation of polystyrene can be produced in different thicknesses. This thermal insulation can be used either indoors or outdoors, on the exterior of the building, stone, brick, or composite cement and paint. . Plaster coating can also be used for the inside. The usual method of insulating a wall with polystyrene (Styrofoam) is to use two walls with retaining insulation or to use a polystyrene sheet on the wall and then build the building facade. Also in the roofing insulation method, polystyrene sheets are used to insulate the ceiling of the building.
The common method of wall insulation with polystyrene (Styrofoam) sheet is to use two walls with retaining insulation or to use polystyrene sheet on the wall. Also, in upside-down roof insulation, polystyrene sheets are used to insulate the roof of the building. For the roof and floor of the building where the compressive resistance is applied to these insulators, a density of 20 to 25 is appropriate. It should be noted that the coating on the polystyrene thermal insulation is required. Polystyrene insulation is produced in different thicknesses.

Packaging and protective foam for all types of goods

Production of packing and protective foam for household and industrial applications up to 6 g / l, extremely delicate and sensitive foam for interior components (air distribution plates), freezers and all types of air conditioners, stoves, laundry, and LCD
The company’s fully automatic machines are equipped with state-of-the-art technology capable of producing up to 40 grams per liter of household and industrial packaging, with highly sensitive components such as internal parts of refrigerators and coolers and a variety of components. EPS

The Benefits of Floor Heating

To your knowledge, floor heating has many advantages over other heating systems.
Pleasant warmth:
Comfort with floor heating system
The floor heating system is a radiant system and radiant heating such as the heat of the sun is the best heating mode for living things.
Highest Comfort:
In homes where floor heating is used, heat is distributed evenly throughout the area, with no need to increase or decrease the heater or radiator valve.
Saving fuel:
The floor heating system is the least used heat system. In this system, with less fuel consumption, all buildings can be heated. The savings in this system are over 5%.
Freedom of action in decoration with floor heating system:
There is no need for a radiator or a heater in the houses that use the heating system. This gives us more freedom to arrange furniture and home decoration.
Cleaner Air:
The heating system is a radiant floor system with very low airflow. This is important because if there is an unpleasant odor or contamination in the house, it will not be transported to all parts of the building by an air displacement and will bring pleasant air to the home.
Cleaning of walls and furniture:
In houses that use thermal systems such as radiators or heaters, the walls around and above the radiators and heaters become black and dirty. This is because the dust in the indoor space sits on the radiator and burns due to the high heat and smoke that sits on the wall and blackens the wall for several years.
This is one of the most common problems with the use of radiators that are generally solved in the floor heating system.

Increasing house value:
This need not be explained. Everyone knows that using modern and efficient systems such as floor heating in homes will increase the value of the house.
Use of different heat sources:
The floor heating system is an ideal system for heating the building. It can be used in different locations and is compatible with different heat sources. These sources include the engine room, wall or ground package, solar water heater, and more.
Wet and humid floors remain drier
In renovated buildings, during the first few years, moisture and humidity are a concern of the building’s occupants. This humidity is low or high depending on the conditions. But in houses where the floor heating system is used, the moisture disappears in a short time and the floor remains dry.
Low depreciation and no maintenance costs
Floor heating is one of the least depreciated heating systems available. The life of the five-layer pipes used in this system is more than 5 years. However, these pipes are also resistant to pressure, decay, and sediment.
The foam panel for the floor heating system is 2 cm thick with EPS polystyrene foam. The system prevents moisture and heat from penetrating the lower surfaces and is structured in such a way that it holds retaining nets for the hot water supply pipes.

Heat-resistant polyethylene pipes are easily installed between the panel grids and the installer can move on top of the panel due to the high strength of the panel and move the building materials. Since the pipes are secured between the panel grids, it is not possible to damage the pipes, and coating operations are performed quickly.

The Benefits of Floor Heating

To your knowledge, floor heating has many advantages over other heating systems.
Pleasant warmth:
Comfort with floor heating system
The floor heating system is a radiant system and radiant heating such as the heat of the sun is the best heating mode for living things.
Highest Comfort:
In homes where floor heating is used, heat is distributed evenly throughout the area, with no need to increase or decrease the heater or radiator valve.
Saving fuel:
The floor heating system is the least used heat system. In this system, with less fuel consumption, all buildings can be heated. The savings in this system are over 5%.
Freedom of action in decoration with floor heating system:
There is no need for a radiator or a heater in the houses that use the heating system. This gives us more freedom to arrange furniture and home decoration.
Cleaner Air:
The heating system is a radiant floor system with very low airflow. This is important because if there is an unpleasant odor or contamination in the house, it will not be transported to all parts of the building by an air displacement and will bring pleasant air to the home.
Cleaning of walls and furniture:
In houses that use thermal systems such as radiators or heaters, the walls around and above the radiators and heaters become black and dirty. This is because the dust in the indoor space sits on the radiator and burns due to the high heat and smoke that sits on the wall and blackens the wall for several years.
This is one of the most common problems with the use of radiators that are generally solved in the floor heating system.
Increasing house value:
This need not be explained. Everyone knows that using modern and efficient systems such as floor heating in homes will increase the value of the house.
Use of different heat sources:
The floor heating system is an ideal system for heating the building. It can be used in different locations and is compatible with different heat sources. These sources include the engine room, wall or ground package, solar water heater, and more.
Wet and humid floors remain drier
In renovated buildings, during the first few years, moisture and humidity are a concern of the building’s occupants. This humidity is low or high depending on the conditions. But in houses where the floor heating system is used, the moisture disappears in a short time and the floor remains dry.
Low depreciation and no maintenance costs
Floor heating is one of the least depreciated heating systems available. The life of the five-layer pipes used in this system is more than 5 years. However, these pipes are also resistant to pressure, decay, and sediment.
The foam panel for the floor heating system is 2 cm thick with EPS polystyrene foam. The system prevents moisture and heat from penetrating the lower surfaces and is structured in such a way that it holds retaining nets for the hot water supply pipes.

Heat-resistant polyethylene pipes are easily installed between the panel grids and the installer can move on top of the panel due to the high strength of the panel and move the building materials. Since the pipes are secured between the panel grids, it is not possible to damage the pipes, and coating operations are performed quickly.

The panel is thermal insulated. It prevents the transfer of heat and cold from the exterior surfaces into the building and acts as a barrier to moisture and sound penetration.
Using the panel reduces energy consumption by 70%.