Portland Cement Type 2
0,00 €Portland cement Type 2 Application
- In cases that a cautious action is needed towards average attack of sulfates.
- Because of hydration reaction in low speed in this type of cement less heat is produced. So this type of cement can be used in almost massive structures like large pillars of big bridges and heavy retaining walls.
- Using this type of cement increases the temperature, this specialty is important in formwork in hot weather.
- In addition to aforesaid cased in all the cases that Portland cement type 1 is applied I mean this type of cement can be used where a special cautious action is not considered.
Labeling Machine OPP – LB 330-3
0,00 €For labeling round shape plastic containers (PET, polyethylene…), metal cans, and glass containers.
Labeling Machine OPP – LB 330-5
0,00 €For labeling round shape plastic containers (PET, polyethylene…), metal cans, and glass containers.
Portland Slag Cement
0,00 €Portland Slag Cement Application
Slag is the material collected on top of blast kiln of smelting iron and known as waste products of steel industry. If slag is gets cold slowly, it is crystal shape that is not consumed a lot. But if we make it cold fast, it gets amorphous or glassy that is used after milling, is applied in cement industry. While milling the slag you have to pay attention that where slag hardness is more that cement, each of them has to be milled separately and finally mix them. In Iran slag cement is divided to 3 kinds that will be said as follows:
- Portland slag cement with less than 25% of slag
- Portland slag anti sulfate cement with 25 to 70% of slag
- Portland slag cement with more than 70% of slag
Portland Pozzolan Cement Application
0,00 €Portland Pozzolan Cement Application
This type of cement more in addition to the general uses, is used in huge structures as well, because It has less hydration heat that Cement type 1 and 2 and the most important advantage of this cement is its more chemical resistance and this type of cement is recommended in environments that the sulfates and Clare attack is more probable. Speed of growing resistance in this type of cement is less than cement type 2 and type 5 but in long term loss of resistance is recovered.
We should pay attention that to increase concrete’s workability you must not increase the proportion of water more than cement, on the other hand because of low speed and hydration heat and slow pozzolan reaction with cement compounds curing concrete with pozzolan cement has to be continuous and wet and in other words the concrete curing situation in comparison with Portland cements has to be provided for longer time.
Totally important specialties of concrete made of Pozzolan concrete are less permeability, high durability and favorable chemical resistant.
Paraffin Wax-Raw material
0,00 €PARS PARAFFIN WAX, is semi refined crude paraffin derived from the Slack Wax dewaxing. This product is produced in two following types:
- Unbleached Paraffin Wax
- Paraffin Wax
Both of them have the same oil content.
Applications
- Candles, torches, tapers, matches, floor polishes
- Car polishes , corrosion protectors
- Electrical industries, cable filling compounds
- Tires and rubber products, as ozone protection
- Paper production
- Carbon paper , crayons and pencils
Residue Wax(Foots Oil)-Raw material
0,00 €PARS RESIDUE WAX (FOOTS OIL), is the residue derived from slack wax de-oiling or sweating in paraffin wax manufacturing process.
Applications
- Tire and rubber products
- Match stick
- Wooden board
- Shoes
- Cosmetic
PARS ENTEGHAL HARARAT- Industrial Oil
0,00 €PARS ENTEGHAL HARARAT oil is high performance product for use in closed indirect heating installations. It is formulated from highly refined base oils that is resistant to thermal cracking and chemical oxidation.
Applications
- Closed systems that the bulk oil temperature ranges are up to 300 oC
Performance Features
- Excellent thermal stability
- Excellent oxidation resistance
- High temperature conductivity coefficient
Performance Levels
- ISO 6743 PART 12, QB
- ISIRI 11298-12QB
PARS FLUSHING-Industrial Oil
0,00 €PARS FLUSHING oil is a very low sulphur content, non-detergent industrial flushing oil that is suitable for flushing, removal of light hydrocarbon based industrial fluid systems.
Applications
- Suitable for use in hydraulic, turbine or heat transfer system requiring cleaning and fluid extraction before recharge.
Performance Features
- Low viscosity
- Good compatibility with most hydraulic, turbine or heat transfer systems materials
PARS SCREW MACHINE- Industrial Oil
0,00 €PARS SCREW MACHINE oil is versatile, moderate extreme pressure neat cutting oil manufactured from high quality base oils and special additives for use in a wide range of severe cutting operations. PARS SCREW MACHINE oil also contains additives to control the generation of oil mist during service.
Applications
- Neat cutting application such as gear cutting , grinding , tapping and , …
Performance Features
- High quality surface finishing
- Good anti – mist formulation
- Very good lubricating and cooling properties
PARS ATRAK VIDJEH- Industrial Oil
0,00 €PARS ATRAK VIDJEH oil is a highly stable oil-in-water emulsion developed for use as a cost effective metalworking fluid. It is formulated with suitable base oils, good additives and emulsifiers to provide in a variety of metalworking fields.
Applications
- Machinery operation
- Drilling
- Sawing
- Grinding
Performance Features
- Very good lubricity
- Excellent emulsion stability
- Without unpleasant odor
- Rust and corrosion resistance
- Excellent cooling properties
- Contains biocide
Performance Levels
- ISO – L- MAA
- ISIRI 2773
PARS QUENCHING- Industrial Oil
0,00 €PARS QUENCHING oil is recommended to use in heat treatment systems of steel alloys. PARS QUENCHING H oil is suitable for marquenching (oil bath temperature up to 170 oC) and the other grades are proposed for cold quenching (oil bath temperature up to 80 oC).
Applications
- Grades 32 to 68 for cold quenching operation
- Grade150 (H) for marquenching operation
Performance Features
- Very low aromatic components
- Excellent thermal stability
- High oxidation resistance
- Non corrosive to steel
Performance Levels
- ISO 6743 PART 14, UHA, UHB
