Electro Water Pump Zagros
0,00 €| Model Number | 31400 |
| Phase | 1 |
| Frequency (Hz) | 50/60 |
| Voltage (V) | 220/230 |
| Power (HP) | 1/60 |
| Speed (rpm) | 2400 |
Electrocardiogram Dena350 – Medical Device
0,00 €3 channel ECG
Simultaneous displaying of 12 leads ECG waveform
Color display and 5’’ touch screen
Ability to record up to 3 channels simultaneously with the paper size of 63mm
Electrocardiogram Dena640 – Medical Device
0,00 €Professional design for using
Color displaying and 4.3 touch screen
12 leads ECG
Different modes of recording (Manual/Auto)
Data storage of 100 records
Electrocardiogram Dena650 – Medical Device
0,00 €6 channel ECG and adjustable
For 2,3 and 4 channels
Simultaneous displaying of 12 leads ECG waveform
Color display and 5’’ touch screen
Ability to record up to 6 channels simultaneously with the paper size of 110mm
Electrostatic Powder Paint with Smoke Reduction Properties
0,00 €Introduction
Use of powder paint as an alternative for liquid paint has created a great evolution in the color quality. Liquid paints create environmental pollution because of possessing evaporative chemical solvents during drying, and they are harmful for human health. The powder paint entered to the market for the first time in 1962. Keeping of 100% solid state, in addition to environmental pollution prevention, has offered incomparable quality against liquid paints to the industry. Powder paints are now taken 15% of the market share and compete with traditional liquid paints. Due to environmental laws on pollution and waste removal, replacement of liquid paints with powder paints becomes more important every day.
Elevator Cabin
0,00 €Using the appropriate skein to the capacity under the cabin
Fully integrated flooring
Inserting the power box of terminal instead of the adhesive tape and the refractory
Installing the buffer
High balance tuning up(vibration sensor)
Reinforced body with special bridges
Using noise suppressor pads in the body(high speeds)
Lifting hook for transportation in four cabin directions
Using special bolts for easier installation of doors
Setting up and installing photocell
The precise design of each panel and kicker according to the type of door
Designing the tray under the cab with adjustable bolt and screw connections
Service plate(MRL)
Embedding the foot guard on the roof of the cabin
Observing the standard of wiring
Usage of customized glue in decoration
Elevator doors
0,00 €The elevator door in a lift system has both safety and decorative aspects at the same time, so it is important to be careful during installation. Elevator door is consisted of different components as follows:
Swing door: Swing doors are less sophisticated because of their less complexity. The frame, the handle, the hinges, the dictator and the contact are the components of a swing door
Automatic Floor door: frames, handles, door seals, shoe covers, contacts are all parts of an automatic door.
Cab Door: All the parts included in the automatic floor door plus the door opening and closing mechanism which include various components such as the header motor, drive and pulleys and belts.
Elevator Frame
0,00 €Elevator frame is a standard and reliable product .
Designing and manufacturing of custom frames appropriate to the building or layout.
Designing without sharp points on all levels for better safety and quality.
Considering the elevator installation standard (easy and safe)
Complete cut with a laser machine without the use of scissors and punches.
Bending with CNC bending machines.
Use of CO2 welding and electrostatic paint in all levels.
Use of standard and galvanized bolts (clamps, washers and chambers).
Complete assembly and disassembly of products with special bolts.
Emulsion Resins
0,00 €Acrylic resins are the product of condensation polymerization of acrylic, methacrylic acids and their derivatives. The use of water based resins is one of the appropriate methods to reduce the amount of organic solvents consumed and as a result toxic volatile. Water based acrylic resins are used in paint, concrete, adhesion, textile industries, etc.
Emulsions-Bitumen & Tar
0,00 €Whatever the end use, application conditions usually require bitumen to behave as a mobile liquid. In principle, there are three ways to make highly-viscous bitumen into a low-viscosity liquid:
- Heat it
- Dissolve it in solvents
- Emulsify it
Bitumen emulsions are two-phased systems consisting of bitumen, water, and one or more additives to assist in formation and stabilization and to modify the properties of the emulsion. The bitumen is dispersed throughout the water phase in the form of discrete globules, typically 0.1 to 50 microns in diameter, which are held in suspension by electrostatic charges stabilized by an emulsifier. Bitumen emulsions can be divided into four classes. The first two are, by far, the most widely used:
- Cationic emulsions
- Anionic emulsions
- Non-ionic emulsions
- Clay-stabilized emulsions
The terms anionic and cationic stem from the electrical charges on the bitumen globules. This identification system originates from one of the fundamental laws of electricity – like charges repel, unlike charges attract. If an electrical potential is applied between two electrodes immersed in an emulsion containing negatively charged particles of bitumen, they will migrate to the anode. In that case, the emulsion is described as “anionic”. Conversely, in a system containing positively charged particles bitumen, they will move to the cathode and the emulsion is described as “cationic”. The bitumen particles in a non-ionic emulsion are neutral and, therefore, will not migrate to either pole. These types of emulsion are rarely
Bitumen emulsions are divided into three categories in terms of setting:
- Rapid-setting (RS)
- Medium-setting (MS)
- Slow-setting (SS)
Cationic RS emulsion is currently the widely used category in Iran. Emulsion setting is irreversible phenomenon which may occur due to the evaporation of the water phase or the attraction of water by stone materials. Throughout this phenomenon, the water phase disappears and bitumen particles will have less space. Then, the bitumen gradually moves towards the surface or coats the aggregate.
Cationic Emulsions
These emulsions are known as cationic because their bitumen aggregates carry positive charges by using Ammonium salts or Amines compounds. They are divided into the following categories:
Enameled Plate & Vase Gift
0,00 €About Enameled Plate & Vase Gift
The art, innovation, and beauty of this package along with unrivaled Arnika saffron get the attention in a way that is impossible to ignore it.
This package contains a crystal pot having 10 g. Negin saffron along with an enameled plate and vase all placed in Termeh box.
Engraved Persian Copper Wall Hanging Plate 105
0,00 €Information
|
Dimensions |
16.5×16.5×3 cm |
| Approximate weight |
160 Gram |
|
Place of production |
Iran |
| Washability |
By hand |
|
Application |
Decorative |
| Material |
Copper |
|
Handling time |
7 Days |
| Glazed veneer |
Yes by Copper |
|
Model |
105 |
